If in the blue area it is acceptably calibrated, and in the green area it is performing well. If this line is mostly in the red area, the lens is poorly calibrated as seen in the example above. The orange line shows the measurement results. The Chart card shows the Quality Ratio chart, which shows how well the lens is performing. In this case, it shows that the lens is in need of calibration, and shows the number of measurements taken. The Test Results Overview card shows a few essential test results. The gauge runs from red on the left representing poor calibration, through to green on the right which represents good calibration the marker is the black line - in the example above pushed to the far left as this lens is not well calibrated. The information obtained is updated as the test runs. The test requires no user interaction and takes a few minutes to run. You can start the test with the Start button in the Status tab, or with the Start button on the test footer bar. When the test starts, there is an information message that is shown to remind you to adjust the focus points for both modes to the centre, but FoCal will currently not verify this, so ensure you have correctly performed this step otherwise the results may be incorrect. If Live View will not start, you will need to stop the test, disconnect the camera and confirm the Live View focus position with the camera disconnected, then reconnect and restart Calibration Check. Note : not all cameras will allow you to enable Live View when connected to a computer e. Once you have successfully confirmed your camera and target setup, you need to ensure that both Live View and non-Live View focus points are set to the centre point. You can access Target Setup from the Target Setup button on the test footer bar, from Camera menu or from the Camera status page. Target Setup utility is an automated utility which will help you do this - all the information you need is here. In order to use Calibration Check, you need to ensure that the camera and target are set up correctly. The display of the final focus calibration results are much clearer - you can compare the crops and the numbers easily before choosing to accept or reject the value.This tool required NO user interaction, and can even run with supported cameras that do not have any focus adjustment capability. And you can also select Near, Far or both for the defocus directions or set to use no defocusing at all. The AF Consistency test has a few extra options available, letting you test more conditions for consistency. This chart shows the quality red is poor, green is good across the aperture range horizontally, and the focus range vertically.Ī little better across the board. How much would you like to know about your camera and lens? You can look more into the details over at the Calibration Check Online Help. But as each test captures so much information, the Details tab lets you dig around in the data. The Summary tab is designed to show you everything you need to know for the test to be useful - in this case, whether you need to calibrate your lens or not. The Summary tab shown above is designed to show you useful information without being overwhelming. This screenshot has introduced a few more features of the FoCal interface. The screenshot above shows the Camera Status page. The Camera and File mode tests have been separated out, reviewing historical information is easier and more useful, navigation around the user interface should be pretty simple and you can even review old tests goat meat protein the same time a new test is running. We think this new user interface is more intuitive, easier to use, more consistent, cleaner and gets you to the proclamation 9993 extended you need faster.
#REIKAN FOCAL PRO REVIEW SOFTWARE#
We would LOVE you to download this release, have a play and give us feedback.Īny feedback - good or bad - will help us tune the software and get it ready for final release. There has been a LOT of testing, based on in-house testing so far this is the most reliable and consistent version of FoCal to date. Which brings us to today, FoCal is nearing completion! We wanted to share it with you to get feedback, hear about what you love and areas that can be tweaked.
#REIKAN FOCAL PRO REVIEW CODE#
FoCal began life in a back room sometime inwith the first official public release toward the end of A complete rework of the user interface and core code followed to bring FoCal 2. We wanted idaho off road racing way to make it clear this is very different to the existing FoCal 2. FoCal is the start of a new naming convention for FoCal releases.
0 kommentar(er)
